Quick answer
Air conditioner size is measured in tons, where one ton is 12,000 Btu per hour of cooling. Most homes use between 1.5 and 5 tons. The right size comes from a load calculation, the industry standard being ACCA Manual J, which accounts for square footage, insulation, windows, sun exposure, ceiling height, ductwork, and local climate. Rules of thumb such as one ton for every 400 to 600 square feet are only a rough starting point. A unit that is too large short cycles and leaves the house humid.
What “tons” means
A ton of cooling is the ability to remove 12,000 Btu of heat per hour. The term goes back to the days of cooling with ice. Residential systems come in half-ton steps from 1.5 to 5 tons, which is 18,000 to 60,000 Btu per hour. A house that needs more than 5 tons generally gets two systems.
Why square footage alone gets it wrong
Two houses of the same size can need very different amounts of cooling. What sets the load is how much heat gets in:
- Insulation and air sealing, the attic above all
- Windows: how many, what kind, and which way they face. West-facing glass is a big load on a Texas afternoon.
- Ceiling height. Air conditioners cool volume, not floor area.
- Ductwork. Ducts running through a hot attic gain heat, and leaky ducts lose cooled air before it reaches the rooms.
- Shade, roof color, and orientation
- People and appliances inside the house
- Climate. Sizing here uses San Antonio’s summer design conditions, including its humidity.
ACCA’s Manual J is the standard method for adding all of that up into a cooling load. When someone sizes your system by glancing at the old unit or asking only for the square footage, they are guessing.
Oversizing is the common mistake
Contractors who want to avoid “it doesn’t keep up” complaints tend to round up. In a humid climate that backfires. An air conditioner removes moisture only while it is running, and it removes the most after the coil has been cold for several minutes. An oversized unit hits the thermostat setting in a few minutes and shuts off, over and over. This is called short cycling. The air is cool, the humidity stays high, and people turn the thermostat down further to feel comfortable.
A correctly sized system runs in long, steady cycles on a hot day. On the very hottest afternoons of the year it may run almost continuously. It was designed to do that.
What to ask a contractor
- How did you arrive at this size?
- Did you look at the attic insulation, the windows, and the ducts?
- If you are recommending a different size from what I have, why?
- Will the existing ductwork handle the airflow this unit needs?
A good answer mentions the house. A poor one mentions only the old unit’s size.
Size and efficiency are separate numbers
Tonnage is how much cooling the unit delivers. SEER2 is how much electricity it uses to deliver it. A quote should state both. See what SEER2 rating is required in Texas.
If you are pricing a new system, our installation page lists what a complete quote should include. Or call (210) 687-7376. Free phone consultation.
Follow-up questions
- How many square feet does a 3-ton AC cool?
- By the common rule of thumb of 400 to 600 square feet per ton, roughly 1,200 to 1,800 square feet. That range is wide for a reason. A shaded, well-insulated house needs much less cooling per square foot than an older house with west-facing glass and a hot attic. Use the rule to sanity-check a quote, not to choose a unit.
- How do I find out what size my current AC is?
- Look at the model number on the outdoor unit’s data plate. It usually contains a two-digit number for capacity in thousands of Btu per hour: 18 is 1.5 tons, 24 is 2 tons, 30 is 2.5 tons, 36 is 3 tons, 42 is 3.5 tons, 48 is 4 tons, and 60 is 5 tons.
- Is a bigger AC better?
- No. An oversized unit cools the air quickly and shuts off before it has run long enough to remove humidity, so the house feels cold and damp. The frequent starts and stops also wear out parts faster and waste electricity.
- Should my new AC be the same size as the old one?
- Only if the old one was right. If it kept the house comfortable and ran in long, steady cycles on hot days, matching it is reasonable. If the house has new windows, added insulation, or an addition, or if the old unit short cycled or never kept up, the size should be worked out again.
- What happens if an AC is too small?
- It runs constantly on hot afternoons and falls behind the thermostat. A slightly undersized unit usually keeps humidity down better than an oversized one, but one that is far too small will not keep the house comfortable in a San Antonio summer.